Newsroom

Understand RF PCB Design – view and solutions

Today, RF circuitry is crammed into a large variety of commercial products. Most of these are handheld wireless devices for medical, industrial, and communications applications. There are also applications in a variety of fields that are migrating from desktop models to become portable communications units. Hence the importance of understanding RF PCB Design.

Ellefen Jiang and colleauges are solving a design problem

The challenges with RF PCB design

There are many new challenges for PCB designers, when handling RF board. Among them, the top four factors are:

  1. RF is far more sensitive to noise, incurring ringing and reflections, which must be treated with great care.
  2. Impedance matching is extremely critical for RF. And, the higher the frequency, the smaller the tolerance becomes. Practically, only if the total length of the trace from the driver to the receiver is greater than 1/16th of the wavelength of the signal, then impedance control of that trace is required (1/16th of the wavelength is called the critical length of the signal). For example, if you are routing a 1GHz signal and its total length is greater than 425 mils, then that trace needs to be impedance controlled.
  3. The return loss must be minimized. At very high microwave frequencies, the return signal takes the path of least inductance. As a result, without good PCB design, the return signal will go through power planes, through a PCB’s multi-layers or through some other route, and it will no longer be an impedance-controlled signal.
  4. Crosstalk is a major issue in high frequency designs. This is because crosstalk is directly proportional to the edge rates of the active line. In this case, the coupled energy from the active line will be superimposed on the victim line. When the board densities increase, the problem of cross talk becomes more critical.

What is RF – Radio Frequency – PCBs?

The RF frequency range is typically from 300 KHz to 300GHz, and designs above 300 KHz are considered RF. The microwave frequency range is anything above 300MHz. There’s a considerable difference between RF and microwave circuits versus typical digital and analog circuits. In essence, RF signals are very high frequency analog signals. Therefore, unlike digital, at any point in time a RF signal can be at any voltage and current level between minimum and maximum limits. Moreover, a single band of signal can be very narrow or very wide and carried upon a very high frequency carrier wave.
In short, RF design is very much different and difficult, in terms of PCB design, comparing to that for high-speed digital signal boards

PCB design solutions

Noise

Properly terminated the signal can solve the reflection or ringing issue. While, optimized return path with proper ground is another way.

Impedance matching

For example, the PCB designer must keep it at 50 ohms – 50 ohms out from the driver, 50 ohms during transmission, and 50 ohms into the receiver.

Return Loss

Ground planes underneath the signals are good at providing this path. Therefore, there should be no discontinuities in the plane underneath the signal all the way from the driver to the receiver. Ground planes help minimize not only ground loop currents but also RF leakage into circuit elements

Cross talk

Always leave adequate space around the signal trace for smooth bends and isolation of the RF signal. Keep all the traces coming out of or going into the transmitter and receiver modules as small as possible. The high-speed signals should be routed as far apart as possible. The distance that the lines run parallel to each other should also be kept to a minimum. All the above measures will reduce the proximity of the two lines and the distance over which the two lines run parallel to each other, hence to reduce cross talk.
Other solutions include reducing the dielectric spacing between the line and its reference plane or introducing a co-planar structure, where a ground plane is inserted between the traces. Terminating the line on its characteristic impedance can also reduce the cross talk by as much as 50 percent.

Avoid losses

Besides factors above, there are other signal losses as well. The first one is the skin effect loss of a signal, specifically the skin effect loss on the trace of a signal.
Dielectric loss is a companion to skin effect loss since both can be created at extremely high frequencies, which is created when electrons flow through a conductor. They bounce back and forth with the electrons on the FR4 PCB substrate, for example. During this interaction, some of the energy from the electrons flowing through a conductor is then transferred to the electrons on the FR4. Consequently, that energy is converted to heat and subsequently lost, and dielectric loss is created.

In such instances, for extremely high frequency microwave circuits it’s best to use polytetrafluoroethylene Teflon, known in the industry as PTFE material. These laminates have a dissipation factor of around 0.001 (compared to FR4’s dissipation factor of 0.02). Secondly, using gold body on RF circuits can greatly reduce the skin losses.

Laminate properties

When using RF circuits, the designer needs to consider the laminate properties, such as the dissipation factor and dielectric constant (Dk) value and its variation. FR4 has a higher dissipation factor than high frequency laminates like Rogers and Nelco. This means that insertion losses are much higher when using FR4.

These losses are also a function of frequency and will increase as frequency rises. Secondly, the Dk value of FR4 can vary as much as 10%. This in turn varies the impedance. High frequency laminates have more stable frequency properties.
Then there is the Dk value itself. When it comes to microwave circuits, the Dk value is tied to the size of the circuit elements, so the designer may be able to decrease the size of the circuit by choosing a laminate with a higher Dk value.

Tips about RF PCB design for designers

In order to achieve more reasonable design and better anti-interference ability for high frequency PCB (Microwave RF PCB), design engineer should consider the tips as following:

  1. Use inner layer as power ground layer, which will have the effect of shielding and even decreasing spurious inductance, shorten length of signal wire, reducing cross interference between signals.
  2. Circuit layout must be turn with 45 degree angle, which will help to reduce high frequency signal emission and coupling between each other.
  3. The shorter the better for length of circuit layout.
  4. The less the better for through holes.
  5. Layout between layers should be in vertical direction, top layer as horizontal direction and bottom layer as vertical direction, because this will help to reduce the signal interference.
  6. Increasing copper on ground layer to reduce the signal interference.
  7. Do package for important signal traces can obviously improve signals anti-interference ability. Of course, we can also do package for interference sources to avoid interference on other signals.
  8. Signal traces layout should avoid loop, but should layout according to chrysanthemum link.
  9. In the power section of integrated circuit, bridging decoupling capacitor.

The top ideas to be kept in mind of PCB designer are:

  1. No RF layout can be perfect, but tuning
  2. Make RF signal 50 ohms
  3. Lay out RF first – ALWAYS
  4. Isolation is important

PCB design guidelines

Get it right from the start with our PCB design guidelines. To prevent getting it wrong from the start, we have put together our design guidelines, to use as a checklist.